Відео

I would use a two stage compressor instead of a two cylinder. Otherwise, awesome video. I will b taking some of these ideas and implementing them into my home build. Thanks!

I've watched this video at least a dozen times and I'm half way through this process! It's really a stroke of engineering genius.. The only thing that I don't understand is how the blood off valve is connected.. Can you explain that part for me?? Thanks a million!!!

Can you measure the same way for an SUV body on frame? To check for frame damage

Hey, can you explain what the vacuum line is for and where it gets attached to? I'm trying to replicate this build and want to make sure I get things right.

i would worry about anywhere the copper touched the pump base the vibration would wear a hole in the copper

The only thing I would do different, would have been to treat the inside of the tank with phosphoric acid, or zinc paint to retard any rust. Fantastic job. I am making one just like it. Thank you.

I don't often clean out my pressure tank, but when I do, I always make certain that I have access to my bong. 😂

Where can we find vehicle measurements? thanks

Moter cycle tank would take care of the rust problem

Are you russian, or ukrainian?

definitely needed to raise the pressure.....but it could be the clear as well, depending if its a speed clear and speed of hardener.

Top job and great video.

be careful with this timing bomb

Where do you get the maps with the exact frame measurements. I have a Mercedes w123 coupe that has some damage on the front and these kind of measurements are gonna be very helpful

Thanks br

How and where do you get the schematics with the measurements from?

What are those red attachments you're using on the stud welder?

Thank you

I like the water bucket, but eventually that water is going to heat up overall you did a great job with that everything

Your videos are awesome, great job, I’m just wondering how many neighbours complains you had lately, I have A LOT just because I do mechanicals at home and my neighbours hate it! Keep the quality and don’t stop posting content!

I appreciate you adding the caveat to cover the pulling chain with a blanket... very important for your and others in the areas safety 👍

Super Gr8 DIY Project. GREAT VIDEO!

I was thinking of buying a new compressor, but after viewing this video I think I will build my own. I’m looking at a 3 cylinder Puma pump with 22 SCFM and a new motor. I also like the cooling coil in the 5 gallon bucket but not real sure if the water will stay cool enough so I might go with a large oil cooler in front of the flywheel.

Just take it to a chop shop,much easier

Love the cooling system idea, I will do that idea great

I really want to duplicate this, water is ideal for cooling

The motor does not put out 5 hp. The peak ratings are 230 V @ 14 A. That means the peak power is 3220 watts. 3220/745.7=4.318 hp peak. Nominal output is going to be in the neighborhood of 3 hp. This the stupid game that compressor mfg play.

Great setup. Too bad it has to live outside in the elements. How about a small protective shed around it? It would be even quieter.

Could you post a link to that bleeder valve that you used? I looked over the video but can’t really tell what kind it is

Good paint job 👍

Excellent video showing auto body repair process in thorough detail! I'm pretty sure most commercial auto body repair shops probably wouldn't be half as careful & thorough in the repair process, as the repair process shown in this great video presentation.

Uuh, take a 3 cylinder 4 stroke engine and convert it to a compressor?

Ive not been at a loss for words in awhile, but.... dude.... inspirational individual right here.

So where exactly do you get frame measurements from? Can anyone help out?

Caramba oque você faz é fantástico parabéns por tudo

Perfeito 👏👏👏

Why are you using copper fittings for water and not copper fittings for gas ?

I suggest you should go with Anest Iwata air compressor, it's a Japanese company but is made india. This is the best pump you would get in market

I have a 20 gal with 2 hp and it can spray and entire car without losing pressure..

Great job! The only suggestions I could come up with is a safety cage around the moving pulleys as well as bolting the tank down to something so that vibrations don't send it off kilter. You might also want to secure your electrical connections a bit better. But, really cool solution.

This things is awesome, great job! I love the water cooling setup

Oil free. That's your problem

Ю брейк

Great DIY project. I would just repaint the main tank (blue) and the motor (black as compressor) to make it look new.

Anything is possible if you give a DIY guy enough time, effort, and money. But remember that the DIY god will probably want a blood donation. Scratch up another win for Harbor Freight.

Hi Fix206, i know this is video is a year old, but how much did all of it cost?

Got yourself a new subscriber. Gonna have to check out this and other videos! I'm all set in the compressor areas. My brother-in-law saw to that! He built me a 5hp Quincy! I was planning on going this route with a cheap pump. However, he had a few parts laying around that become a whole compressor.

15:40 someone lied to him and said, " Yeah that is six inches."

Never seen anyone put the compound directly onto the surface and not onto the mop before

Login the redneck ingenuity with fuk all tools lol brilliant